Sanyo Camera Accessories VSE 2300 User Guide

INSTRUCTION MANUAL  
VSE-2300 &  
VSE-2400 SERIES  
Cylindrical  
Environmental Camera Housings  
About this manual  
Before installing and using this unit, please read  
this manual carefully. Be sure to keep it available for  
later reference.  
 
SAFETY PRECAUTIONS  
SICHERHEITSVORKEHRUNGEN  
VORSICHT: UM EINEN ELEKTRISCHEN  
SCHLAG ZU VERMEIDEN, ABDECKUNG  
NICHT ENTFERNEN. WARTUNGEN ALLER  
ART QUALIFIZIERTEM PERSONAL  
ÜBERLASSEN.  
CAUTION: TO REDUCE THE RISK OF  
ELECTRICAL SHOCK, DO NOT OPEN COVERS.  
NO USER SERVICEABLE PARTS INSIDE. REFER  
SERVICING TO QUALIFIED SERVICE  
PERSONNEL.  
This label may appear on the bottom of the unit due to space  
limitations.  
Aus Platzgründen kann diese Warnung auf der Unterseite des  
Gerätes angebracht sein.  
The lightning flash with an arrowhead symbol within  
an equilateral triangle is intended to alert the user  
to the presence of uninsulated "dangerous voltage"  
within the product's enclosure that may be of  
sufficient magnitude to constitute a risk of electric  
shock to persons.  
Das Blitzsymbol im gleichseitigen Dreieck soll den  
Benutzer auf nicht isolierte "Hochspannung" im  
Gehäuse aufmerksam machen, die eventuell stark  
genug ist, um einen elektrischen Schlag zu  
verursachen.  
Das Ausrufezeichen im gleichseitigen Dreieck soll  
den Benutzer auf wichtige Bedienungs- und  
Wartungsanleitungen in der dem Gerät beigefügten  
Literatur aufmerksam machen.  
The exclamation point within an equilateral triangle  
is intended to alert the user to presence of  
important operating and maintenance (servicing)  
instructions in the literature accompanying the  
appliance.  
PRECAUCIONES DE SEGURIDAD  
SECURITE  
PRECAUCION: PARA REDUCIR EL RIESGO DE  
CHOQUE ELÉCTRICO, FAVOR NO ABRIR LA  
CUBIERTA. ESTE EQUIPO NO CONSTA DE  
PIEZAS O PARTES QUE REQUIEREN SERVICIO  
O MANTENIMIENTO. PARA REPARACIONES  
FAVOR REFERIRSE A UN TÉCNICO  
DANGER: POUR ÉVITER TOUT RISQUE  
D'ÉLECTROCUTION, NE PAS OUVRIR LE  
BOÎTIER. IL N'Y A PAS DE PIÈCES  
REMPLAÇABLES À L'INTÉRIEUR. POUR  
TOUTE RÉVISION, S'ADRESSER À UN  
TECHNICIEN SPÉCIALISÉ.  
CALIFICADO.  
Debido a limitaciones de espacio, esta etiqueta puede aparecer en  
la parte inferior de la unidad.  
En raison de limitation de place, cette étiquette peut être placée  
sur le dessous de l'appareil.  
El símbolo representado por un relámpago con punta  
de flecha dentro de un triángulo equilátero, se  
muestra con el objetivo de alertar al usuario que  
existen "voltages peligrosos" sin aislamiento, dentro  
de la cubierta de la unidad. Dichos voltages pueden  
ser de tal magnitud que constituyen un riesgo de  
choque eléctrico a personas.  
L'éclair fléché dans un triangle équilatéral, avertit  
l'utilisateur de la présence d'une "tension  
dangereuse" non isolée à l'intérieur de l'appareil et  
d'une valeur suffisante pour constituer un risque  
d'électrocution.  
Le point d'exclamation contenu dans un triangle  
équilatéral, avertit l'utilisateur de la présence, dans la  
documentation qui accompagne l'appareil, de  
consignes d'utilisation et de maintenance  
importantes.  
El símbolo de exclamación dentro de un triángulo  
equilátero, se muestra con el objetivo de alertar al  
ususario de que instrucciones de operación y  
mantenimiento importantes acompañan al equipo.  
3
 
CONTENTS  
1
2
3
4
5
6
6.2  
6.1  
6.2  
6.3  
6.4  
6.5  
6.6  
6.7  
6.8  
6.9  
UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
CARE AND MAINTENANCE . . . . . . . . . . . . . . . .4  
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . .6  
Maximum Camera/Lens Size . . . . . . . . . . . . . . . . . .5  
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
Cable Requirements . . . . . . . . . . . . . . . . . . . . . . . .5  
Housing Mounting . . . . . . . . . . . . . . . . . . . . . . . . . .6  
Cover Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . .6  
Camera/Lens Installation . . . . . . . . . . . . . . . . . . . . .6  
Camera/Lens Wiring . . . . . . . . . . . . . . . . . . . . . . . .7  
Video Coax Connection . . . . . . . . . . . . . . . . . . . . .9  
Lens Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
Camera/Lens Adjustment . . . . . . . . . . . . . . . . . . . .9  
6.10 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
6.11 Fuse Replacement . . . . . . . . . . . . . . . . . . . . . . . . .10  
WARRANTY INFORMATION . . . . . . . . . . . . . .11  
1 UNPACKING  
Unpack carefully. This is mechanical equipment and should be  
handled with care.  
The shipping carton is the safest container in which the unit  
may be transported. Save it for possible future use.  
Check for the following:  
2 SERVICE  
Housing (with correct model number).  
Hardware Kit - VSE-2300 Series Models:  
1 1/4-20 x 3/8-in Button Head Screw.  
2 1/4-20 x 1/2-in Button Head Screw.  
2 1/4-in Spring Washers.  
If the unit ever needs repair service or parts, the customer  
should contact Sanyo Technical Support 1-(888)-66SANYO.  
3 CARE AND MAINTENANCE  
1 5/16-in Flat Washer.  
2 Fittings, 3/8-in NPT.  
2 Rubber Plug, 1/2-in NPT.  
1 Nut, 3/8-in NPT.  
Regularly scheduled maintenance will help prolong the  
operation life of this unit. Clean the viewing window as  
needed with a mild, nonabrasive detergent in water and a soft  
cloth.  
2 Fittings, 1/2-in NPT.  
2 Nut, 1/2-in NPT.  
1 Spacer Block.  
Hardware Kit - VSE-2400 Series Models:  
1 1/4-20 x 3/8-in Button Head Screw.  
3 1/4-20 x 1/2-in Button Head Screw.  
1 1/4-20 x 5/8-in Button Head Screw.  
1 1/4-20 x 3/4-in Button Head Screw.  
1 1/4-20 x 7/8-in Button Head Screw.  
2 1/4-in Spring Washers.  
4 DESCRIPTION  
Cylindrical Environmental Camera Housings  
Model Number: VSE-2300 and VSE-2400 Series  
Highlights:  
• For 1/4-inch, 1/3-inch, and 1/2-inch CCD Cameras  
• Available in Multiple Sizes  
1 5/16-in Flat Washer.  
2 Fittings, 3/8-in NPT.  
• Aluminum and Advanced Polymer Construction  
• Easy Installation & Full Camera Accessibility  
• Feed-through Wiring Option through the Mounting Base  
• Liquid Tight Fittings on Rear of Housing  
• Multiple Mounting Configurations Available  
• Available with Preinstalled Heater or a Preinstalled  
Heater & Blower  
2 Rubber Plug, 1/2-in NPT.  
1 Rubber Plug, 3/8-in NPT.  
1 Nut, 3/8-in NPT.  
2 Fittings, 1/2-in NPT.  
2 Nut, 1/2-in NPT.  
4 Spacer, 0.4 mm.  
4 Spacer, 3.2 mm.  
• Heater/Blower Combination Minimizes fogging and  
Extends Temperature Limits  
• NEMA 4 and IP65 Weatherproofing Standards  
If an item appears to have been damaged in shipment, replace  
it properly in its carton and notify the shipper. If any items  
are missing, contact Sanyo.  
4
 
ELECTRICAL SPECIFICATIONS  
Camera Mounting: Removable camera bracket. Mounted  
with two screws.  
Preinstalled Heater or  
Model Number  
Voltage/Power (V/W)  
Heater/Blower1  
VSE-2300  
---  
Construction: Aluminum cover, aluminum base, aluminum  
mounting foot, polycarbonate faceplate, glass reinforced  
polycarbonate end caps, neoprene gasket, ethylene propylene  
seal, and all stainless steel hardware.  
VSE-2300H  
VSE-2300HB  
Heater  
24/23  
24/25  
Heater/Blower  
VSE-2400  
---  
Finish: Gray  
VSE-2400H  
VSE-2400HB  
Heater  
24/23  
24/25  
Heater/Blower  
ENVIRONMENTAL & SAFETY SPECIFICATIONS:  
1. The heaters and blowers for all models operate at 50/60 Hz.  
Temperature: At external temperature of –40 °F to 122 °F  
(–40 °C to 50 °C) maintains internal temperatures between  
–4 °F to 131°F (–20 °C and 55 °C) with heater/blower.  
Do Not Exceed 30 VAC Input on 24 VAC models.  
Operation above 30 VAC violates low voltage operation  
(Class 2 Specifications). Normal operation is 24 VAC.  
Salt Atmosphere: MIL-STD-810E, Method 509, Procedure 1.  
Enclosure Protection: IP65, Designed to meet NEMA 4.  
Safety: UL, cUL, CE.  
TUV Approved 24 VAC Models  
Caution: Use an approved power supply incorporating  
reinforced insulation from primary to secondary to isolate  
unit from Mains.  
MECHANICAL SPECIFICATIONS  
Model Number Maximum Camera and Lens  
Weight  
5 ACCESSORIES:  
2.68 W x 2.1 H x 10.5 L in  
VSE-2300  
~4 lbs. (1.8 kg)  
~4 lbs. (1.8 kg)  
~4 lbs. (1.8 kg)  
(68 x 54 x 267 mm)  
SUNSHIELDS:  
2.68 W x 2.1 H x 10.5 L in  
(68 x 54 x 267 mm)  
VSE-2300H  
Provides protection from the direct rays of sun and  
promotes cooling to reduce internal housing temperatures.  
Strongly recommended for housing to be used outdoors.  
VSE-SS2300: For VSE-2300 Series housings.  
VSE-SS2400: For VSE-2400 Series housings.  
2.68 W x 2.1 H x 8.5 L in  
(68 x 54 x 216 mm)  
VSE-2300HB  
2.8 W x 2.8 H x 11 L in  
VSE-2400  
~5 lbs. (2.3 kg)  
~5 lbs. (2.3 kg)  
~5 lbs. (2.3 kg)  
(71 x 71 x 279 mm)  
2.8 W x 2.8 H x 11 L in  
(71 x 71 x 279 mm)  
VSE-2400H  
2.8 W x 2.8 H x 9 L in  
(71 x 71 x 229 mm)  
MOUNTS:  
VSE-2400HB  
MTS-2000 Mount Wall Mount: Feed-through mount  
attached to the foot of housing for VSE-2300 & VSE-2400  
Series housings.  
Cable Entry:  
VSE-2300 Series housings have two liquid tight rear fittings  
that accept cable diameters from 0.17 in to 0.47 in (4.3 mm  
to 11.9 mm). Two bottom feed-through liquid tight fittings  
accept cable diameters from 0.18 in to 0.31 in (4.6 mm to 7.9  
mm).  
MTS-2030 J-mount: Feed-through J-mount for VSE-2300 &  
VSE-2400 Series housings allows housing to be mounted from  
ceiling.  
MTS-2040 Pole Mount Adapter: For use with MTS-2000  
Wall Mount.  
VSE-2400 Series housings have three liquid tight rear fittings,  
two of which accept cable diameters from 0.17 in to 0.47 in  
(4.3 mm to 11.9 mm) and one that accepts cable diameters  
from 0.18 in to 0.31 in (4.6 mm to 7.9 mm). Two bottom  
feed-through liquid tight fittings accept cable diameters from  
0.18 in to 0.31 in (4.6 mm to 7.9 mm).  
MTS-2050 Pedestal Mount: 8-inch feed-through mount  
for the VSE-2300 & VSE-2400 Series housings.  
Tamperproof Kit: Contains tamper resistant screws and  
bit key to tamperproof up to five housings. Call factory.  
Window: 0.12 in (3 mm) thick UV-stabilized polycarbonate.  
Housing Mounting: Four (4) available 1/4-20 tapped holes.  
Only one set of two is required for mounting.  
5
 
6 INSTALLATION  
6.3 Housing Mounting  
This installation should be made by qualified service  
personnel and conform to the National Electrical Code and  
applicable local codes.  
1. Use the two 1/4-20 x 0.50-inch screws and 1/4-inch spring  
washers provided in the hardware kit to mount the  
housing to a mount or a pan/tilt. The spring washers must  
be used for the screws to thread properly.  
6.1 TOOLS REQUIRED  
- Small flat blade screwdriver.  
- Phillips screwdriver (P2).  
- Adjustable wrench.  
- Wire cutter/stripper/crimper tool.  
- 5/32-in (or 4 mm) hex wrench.  
2. The outermost set of 1/4-20 threaded holes are for  
mounting to feed-through mounts and the innermost 1/4-  
20 holes are for mounting to all other mounts and  
pan/tilts.  
6.4 Cover Removal  
6.2  
CABLE REQUIREMENTS  
1. Loosen the top two screws on the rear of the housing.  
These screws are captive and will not come out all the  
way. Do not remove the bottom two screws. See  
Figure 1.  
VIDEO TRANSMISSION (COAXIAL)  
Cable Type:  
Cable Size:  
RG-59/U for runs < 300 m (1000 ft).  
RG-11/U for runs < 600 m (2000 ft).  
Outside diameter between  
4.6 mm (0.181-in)–7.9 mm (0.312-in).  
Round.  
Cable Shape:  
Shield:  
LoosenThese Screws  
> 93% Braided copper shield.  
Center Conductor: Stranded copper center.  
DC Resistance:  
< 15 Ohms/1000 (RG-59/U).  
< 6 Ohms/1000 (RG-11/U).  
Cable Impedence: 75 Ohm.  
Agency Rating:  
Environmental:  
UL.  
Outdoor rated.  
Temperature Rating:> 80 °C.  
Sources: Belden 9259.  
Belden 9238.  
Do Not Remove  
INPUT POWER CORD - NORTH AMERICAN  
Cable Type:  
Cable Size:  
SJTOW-A rated.  
Figure 1: Loosening Captive Screws  
Outside diameter between  
4.3 mm (0.170 in)–11.9 mm (0.470 in).  
Round.  
3 conductor version and  
2 conductor version.  
UL/C.S.A., UL VW-1.  
Outdoor rated.  
2. Grasp the housing's front cap and pull forward. Do not  
squeeze the cover itself. This will make it difficult to slide  
off the cover. See Figure 2.  
Cable Shape:  
Conductors:  
Grasp Here  
Agency Rating:  
Environmental:  
Temperature Rating:105 °C.  
Voltage Rating:  
Sources:  
300 V.  
Belden 19506.  
Belden 19509.  
Northwire 573939.  
LENS CONTROL CABLE  
Cable Type:  
Cable Size:  
Jacketed multiconductor cable.  
Figure 2: Removing the Cover  
Outside diameter between  
4.3 mm (0.170 in)–11.9 mm (0.470 in).  
Round.  
3. The cover is attached to the base. Allow the cover to  
dangle from the base.  
Cable Shape:  
Shield:  
Overall shielding.  
Conductors:  
Stranded 20 to 16 AWG wire.  
No. of Conductors: 4 and 8.  
Conductor  
Insulation:  
Sources:  
Color coded.  
Belden 9552.  
Belden 9554.  
6
 
6.5 Camera/Lens Installation  
VSE-2400 Series:  
1. Loosen the two screws holding the camera bracket to the  
base. It is not necessary to remove them completely. See  
Figure 3.  
3. Attach the lens to the camera.  
4. Use the various 1/4-20 screws and spacers provided to  
mount the camera and the lens to the camera bracket.  
6.6 Camera/Lens Wiring  
WARNING: Only use the cables specified  
under "INSTALLATION, Cable Requirements"  
for wiring of all cameras and lenses.  
6.6.1 Fittings  
1. The two large 1/2-inch NPT fittings accept round cable  
with diameters from 4.3 mm (0.17-inch) to 11.9 mm  
(0.47-inch). The small fittings will accept cables with  
diameters from 4.6 mm (0.181-inch) to 7.9 mm (0.312-  
inch).  
Camera  
Bracket  
LoosenThese  
Screws  
Be sure to securely tighten all fittings to ensure  
a liquid-tight seal. Failure to do so could allow  
water to enter the housing and damage the  
camera and lens.  
If a sealant is to be used, be sure it is a neutral cure type.  
Sealants that release acetic acid may harm camera electronics.  
Figure 3: Removing the Camera Bracket  
Use of "drip loops" is recommended on the  
wiring outside of the rear end cap.  
2. Remove the camera bracket from the base. If you are  
using the feed-through feature, refer to Section 6.8.3 at  
this time.  
6.6.2 Conduit  
These housings are designed to allow conduit to be directly  
connected.  
Mounting fixed lens cameras in VSE-2300 and VSE-2400  
Series Housings.  
1. Attach the lens to the camera.  
1. Remove the rear fittings and attach the conduit and  
conduit fittings directly to the housing rear cap. The holes  
accept 1/2-inch conduit fittings and PG 13.5 conduit  
fittings. Any unused holes can be covered using the plugs  
provided in the hardware kit.  
2. Use the 1/4-20 x 3/8-inch screw to mount the camera to  
the camera bracket. The lens should extend  
approximately 6 mm (0.25-inch) from the front of the  
camera bracket. See Figure 4.  
6.6.3 Feed-through Wiring  
These housings have the capability of having the cabling feed  
through the foot of the housing. This requires the use of  
feed-through mounts like the MTS-2000, or MTS-2030  
J-mount.  
Camera  
Camera  
Bracket  
1. Prior to mounting the camera. Remove the two dome  
plugs located inside the housing. See Figure 7.  
6.4 mm  
0.25 in  
1/4-20 x 3/8 Screw  
Figure 4: Attaching the Camera  
7
 
3. The terminal block provided on /x0 units accepts wire  
Rear Cap  
2
ranging from 20 to 14 AWG or 1.5 mm . The terminal  
block provided on /x1 units accepts wire ranging from 18  
2
to 12 AWG or 2.5 mm . When using larger wire sizes,  
splice to a smaller size wire at the terminal block end.  
The splice may need to be enclosed in a junction box if it  
does not pass through the fittings.  
RemoveThese  
Dome Plugs  
1/2-inch  
Rubber Plugs  
4. A screw/terminal lug is provided for securing a safety  
ground. To attach the safety grounding wire (green 115  
volt, green/yellow 230 volt), first unscrew the terminal lug  
and strip and crimp the grounding wire into the lug.  
Attach the terminal lug to the bracket using the M4 x 10  
screw provided. See Figure 8.  
Foot  
3/8-inch NPT  
Fitting  
Figure 8: Power Connections - Nonfan Units  
Figure 7: Feed-through Wiring  
Screw  
2. Screw the two 3/8-inch NPT fittings into the foot of the  
housing.  
Fuseholder  
Terminal  
Lug  
Ground  
3. Pull the cabling through the fittings and into the housing.  
.
.
.
Neutral  
Tighten the fitting to 4.0 N m to 4.5 N m (35 in lb to  
.
40 in lb). This torque rating is approximately 1 to 1-1/2  
Line  
Terminal Lug  
(LTC 9480/00 only)  
turns past the point where the fitting starts to grip the  
wire. Failure to do so will result in water damage to all  
electronic parts.  
M4 Nut (Use a  
7 mm wrench)  
4. Attach the foot to the top bracket of the mount.  
Figure 9: Power Connections - Fan Units  
5. Cover the holes in the rear cap with the rubber plugs  
provided. Push in until flush and then release.  
6.6.4 Power Connections  
Power connection into the housings is to be supplied through  
a minimum type UL Standard "SJ" cord acceptable for  
outdoor use. Installation must conform to acceptable NEC  
and local codes. For 24 volt cameras, use the chart below for  
selecting the proper wire size.  
Ground  
Terminal Lug  
Recommended Maximum Cable Lengths for Housings  
Equipped with 24 Volt Cameras, Heaters, and  
Blowers  
Neutral  
Line  
Screw  
Fuseholder  
Wire Size  
Housing  
meters  
28.6  
Distance  
feet  
94  
2
mm  
AWG  
0.5  
1
20  
18  
16  
14  
12  
10  
8
45.7  
150  
1.5  
2.5  
4
70.1  
230  
115.5  
183.8  
292.6  
464.2  
379  
603  
6
960  
5. Pull any excess wire out of the housing and tighten the  
10  
1523  
.
.
.
.
fitting to 8.5 N m to 9.0 N m (75 in lb to 80 in lb). This  
torque rating is approximately 1 to 1-1/2 turns past the  
point where the fitting starts to grip the wire.  
2
NOTE: The use of wire sizes larger than 1.5 mm (14 AWG) will require a  
splice in order to accomodate the terminal block.  
1. Install one of the large 1/2-inch NPT fittings into one of  
the holes in the rear cap. The terminal block side is  
preferable. If you are using the feed-through option,  
ignore this step.  
Failure to do so will allow water to enter and damage all  
electronic parts.  
2. Route the power cable through the fitting in the rear cap  
or one of the feed-through fittings in the foot.  
8
 
Be sure to securely tighten all fittings to ensure a  
liquid-tight seal. Failure to do so could allow water to  
enter the housing and damage the camera and lens.  
6.8 Lens Wiring  
WARNING: Only use the cables specified  
under "INSTALLATION, Cable Requirements"  
for wiring of the lens.  
6. Connect the supply power wires to the left side or the  
top side of the terminal block provided. Strip no less than  
6 mm (0.25-inch) and no more than 8 mm (0.31-inch) of  
insulation away from the wire. Be sure not to nick the  
wires.  
1. Install the last 1/2-inch NPT fitting into the remaining hole  
in the rear cap. Zoom lenses can only be installed into  
VSE-2400 housings.  
2. If installing a zoom lens, insert the lens control cable  
through the last fitting at the rear of the housing. Attach  
the lens wiring to the lens mating connector and connect  
it to the lens. If mating connector is not available, connect  
directly to the lens cable. Pull any excess wire out of the  
7. Cut the camera power cord, leaving enough cable to  
allow connection to the terminal block. Strip no less than  
6 mm (0.25-inch) and no more than 8 mm (0.31-inch) of  
insulation away from the wire. Be sure not to nick the  
wires. Connect these wires to the left side or the top  
side of the terminal block.  
.
.
housing and tighten the fitting to 8.5 N m to 9.0 N m  
.
.
(75 in lb to 80 in lb). This torque rating is approximately 1  
to 1-1/2 turns past the point where the fitting starts to  
grip the wire. Failure to do so will result in water damage  
to all electronic parts.  
8. On heater and heater/blower units, make sure the heater  
and fan wires stay connected to the terminal block.  
6.7 Video Coax Connection  
NOTE: See specification on lens cord for correct plug  
WARNING: Only use the cables specified under  
"INSTALLATION, Cable Requirements" for  
wiring of the video coax connection.  
connection.  
Be sure to securely tighten all fittings to  
ensure a liquid-tight seal. Failure to do so  
could allow water to enter the housing and  
damage the camera and lens.  
1. For VSE-2300 versions, install a 1/2-inch NPT fitting into  
the remaining hole in the rear cap. For VSE-2400 versions,  
install a 3/8-inch NPT fitting through the center small hole  
of the rear cap.  
3. If using a pan/tilt with a feed-through cable, insert  
the camera/lens function cable in through the left fitting at  
the rear of the cradle. Wire the functions as described  
above or as needed.  
2. Route the video coax cable through one of the fittings  
installed in step 1 or one of the feed-through fittings in  
the base.  
Use of "drip loops" is recommended on the  
wiring outside of the rear end cap.  
3. Attach BNC connector to the coax and connect it to the  
camera. Pull any excess wire out of the housing and  
.
.
.
tighten the fitting to 8.5 N m to 9.0 N m (75 in lb to 80  
6.9 Camera/Lens Adjustment  
.
in lb). This torque rating is approximately 1 to 1-1/2 turns  
Verify camera and lens operation before final assembly of the  
cradle into the housing. Adjust the camera focus and iris as  
necessary. See individual camera instructions.  
past the point where the fitting starts to grip the wire.  
Failure to do so will result in water damage to all  
electronic parts.  
6.10 Final Assembly  
Be sure to securely tighten all fittings to ensure a  
liquid-tight seal. Failure to do so could allow water to  
enter the housing and damage the camera and lens.  
1. Use the plugs or fittings provided to plug any remaining  
holes in the rear cap.  
2. Reinstall the cover. Align the bottom of the cover ribs  
with the top of the base. Slide the cover onto the base.  
Make sure the seal is not folded over or torn. Use  
silicone grease to lubricate the seals if necessary. See  
Figure 10.  
Use of "drip loops" is recommended on the wiring  
outside of the rear end cap.  
9
 
See Detail  
Cover Rib  
Seal  
Top of Base  
Figure 10: Reinstalling the Cover  
3. As the cover nears the rear cap, make sure the captive  
screws in the back are not blocking the cover from  
engaging into the rear cap.  
4. Screw the two rear captive screws into the housing.  
6.11 Fuse Replacement  
1. To replace a fuse, take a flat blade screwdriver and twist  
the top of the fuseholder counterclockwise about a  
quarter of a turn. The fuse is spring loaded so it will eject.  
2. Replace the fuse with a fuse that has the same current  
rating. The fuse is a 5x20 mm slow blow cartridge type  
fuse. Littelfuse Series 218 are recommended.  
10  
 
SANYO INDUSTRIAL VIDEO  
HOUSINGS OR INTEGRATED CAMERA/LENS/HOUSING PACKAGES  
OBLIGATIONS  
In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s  
expense, unless specifically stated otherwise in this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained  
by calling the toll- free number listed below.  
For product operation, authorized service center referral, service assistance or problem resolution, call  
CUSTOMER INFORMATION 1- 800- 421- 5013  
Weekdays 8: 30 AM – 5: 00 PM Pacific Time  
For accessories and/ or parts, call  
PARTS ORDER INFORMATION 1- 800- 726- 9662  
Weekdays 8: 30 AM – 5: 00 PM Pacific Time  
THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA,  
EXCLUDING ALL U. S. TERRITORIES AND PROTECTORATES. THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL  
PURCHASER OR END USER. THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE  
AUTHORIZED SANYO SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED.  
Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO Fisher Company warrants this SANYO product against defects in  
materials and workmanship for the periods specified below. SFC will repair or replace (at its option) the product or any of its parts which fail to  
conform to this warranty. The warranty period commences on the date the product was first purchased or rented at retail.  
LABOR  
PARTS  
3 YEARS  
3 YEARS  
EXCLUSIONS  
This warranty does not cover (A) the adjustment of customer- operated controls as explained in the appropriate model’s instruction manual, or  
(B) the repair of any product whose serial number has been altered, defaced or removed.  
This warranty shall not apply to the cabinet or cosmetic parts, batteries or routine maintenance.  
This warranty does not apply to uncrating, setup, installation, removal of the product for repair or reinstallation of the product after repair.  
This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any  
malfunction, defect or failure caused by or resulting from unauthorized service or parts, improper maintenance, operation contrary to furnished  
instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect power line voltage, fire,  
flood or other Acts of God, or normal wear and tear.  
The foregoing is in lieu of all other express warranties and SFC does not assume or authorize any party to assume for it any other obligation or  
liability.  
SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED, WITH REGARD TO THIS PRODUCT (INCLUDING THE WARRANTIES  
OF MERCHANTABILITY AND FITNESS). IN NO EVENT SHALL SFC BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL  
DAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS  
OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL. SFC’S LIABILITY FOR ANY AND ALL LOSSES AND  
DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER, ARISING OUT OF OR IN CONNECTION WITH THE SALE, USE OR  
OWNERSHIP OF THIS PRODUCT INCLUDING WARRANTOR’S NEGLIGENCE, OR ALLEGED DAMAGED OR DEFECTIIVE GOODS,  
WHETHER SUCH DEFECTS ARE DISCOVERABLE OR LATENT, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE  
PRODUCT.  
ATTENTION  
For your protection in the event of theft or loss of this product, please fill in the information below for you own personal records.  
Model No _____________________________________________ Serial No. __________________________________________  
(Located on back or bottom side of unit.)  
Date of Purchase ______________________________________ Purchase Price ______________________________________  
Where Purchased ___________________________________________________________________________________________  
11  
 
Sanyo Fisher Company  
Security Video Division  
21605 Plummer Street  
Chatsworth, CA 91311  
Tel: (818) 998-7322  
Fax: (818) 717-2716  
Technical Support: (888) 66SANYO  
100 0004 001 SAN 6/02  
Printed in USA  
 

QSC Audio Portable Speaker 922dz User Guide
Q See Cable Box QT518 814 User Guide
Q See Security Camera QC40198 814 User Guide
Radica Games Games 75043 User Guide
Ramsey Electronics Stereo Amplifier QAMP40 User Guide
RCA DVR AVC 776 User Guide
Rheem Water Heater HE45 160 User Guide
Samsung Security Camera SCC C6407P User Guide
Samsung Switch SCLSeries User Guide
Seagate Computer Drive STCD500102 User Guide